English German
 

 

Power Supply
Raid Module
Card Reader
 
Zippy R2G-5500V4V 2U Redundant
Peripheral > Power Supply > Zippy >R2G-5500V4V


R2G-5500V4V
  • Output Wattage: 500W
  • Best Solution for: Server, Workstation, Storage System, IPC
  • Dimension:
    276.00 x 101.00 x 82.00 (mm)
    10.87 x 3.98 x 3.23 (inch)
AC INPUT SPECIFICATION
 
  • VOLTAGE: 90 ~ 264VAC FULL RANGE
  • FREQUENCY: 47~63HZ
  • INPUT CURRENT:8A/4A (115 / 230 VAC) POWER MODULE
  • INRUSH CURRENT:60A/80A MAX. FOR 115/230 VAC POWER MODULE
  • DC INPUT SPECIFICATION
    OUTPUT VOLTAGE
    OUTPUT CURRENT
    REGULATION
    OUTPUT
    MIN.(A)
    MAX.(A)
    LOAD
    LINE
    RIPPLE & NOISE
    MAX.[P-P]
    +5V
    0.5
    25
    ± 5%
    ± 1%
    50mV
    +12V
    2
    40
    ± 5%
    ± 1%
    120mV
    -12V
    0.2
    0.8
    10%
    ± 1%
    150mV
    +3.3V
    0.5
    25
    ± 5%
    ± 1%
    50mV
    +5VSB
    0.1
    3.5
    5%
    ± 1%
    50mV
    Remarks:
    * +5V AND +3.3V TOTAL OUTPUT MAX : 170W
    * TOTAL OUTPUT MAX: 500W

     

    • TEMPERATURE RANGE:OPERATING 0℃~40℃, OPERATING TEMPERATURE: -20℃~80℃
    • HOLD UP TIME:16mS MINIMUM AT FULL LOAD & NOMINAL INPUT VOLTAGE
    • DIELECTRIC WITHSTAND:INPUT/OUTPUT 1500 VAC FOR 60 SECOND INPUT TO FRAME GROUND 1500 VAC FOR 60 SECOND
    • EFFICIENCY:TYPICAL >80% AT 115VAC, 20%~100% MAX LOAD
    • POWER GOOD SIGNAL:ON DELAY 100mS TO 500mS
    • OVER POWER PROTECTION:110% ~ 180%
    • OVER VOLTAGE PROTECTION:+5V→5.9V~6.7V、+12V→13.0V~15.0V、+3.3V→3.9V~4.3V SHORT
    • SHORT CIRCUIT PROTECTION:+5V, +3.3V, +12V, -12V, AUTO-RECOVERED: +5VSB
    • OVER CURRENT PROTECTION: +3.3V: 27.5~37.5A, +5V: 27.5~37.5A, +12V: 44~76.8A
    • EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B
    • SAFETY: TO MEET UL, CUL, TUV, CCC
    • REMOTE ON/OFF CONTROL THE POWER SUPPLY SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE/ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY). AS LOGIC LEVEL IS LOW,OUTPUTS VOLTAGE WERE ENABLE, AS LOGIC LEVEL IS HIGH,OUTPUTS VOLTAGE WERE DISABLE.
    • N+1 REDUNDANCY FUNCTION
    • HOT-SWAPPABLE FUNCTION
    • CURRENT/BALANCE LOAD SHARING DESIGN
    • +3.3V REMOTE SENSING
    • ISOLATION: BUILT-IN IN POWER MODULE
    • POWER FACTOR CORRENTION: ACTIVE (MEET IEC-1000-3-2)
    • COOLING: 40mm DC FANS (one module)
    • DIMENSION:276(D)101(W)82(H) mm
    • *THE POWER-SUPPLY IS FOR CHASSIS-ASSEMBLY ONLY AND IS NOT ALLOWED TO BE OPERATED AS STAND-ALONE COMPONENT. FINAL ASSEMBLY HAS TO COMPLY WITH CORRESPONDING EMC- AND SAFETY-REGULATIONS.